wear test

磨耗试验

Examples

  • In this paper the testing results of performance of MT-1 model vacuum friction and wear test machine which was made by ourselves have been described .

    本文介绍了对自行研制的MT－1型真空摩擦 磨损 试验机〔1，2〕的性能的测试结果，并且进行了分析。

  • A Pin-on-disk wear test equipment set in S-570 SEM is introduced in this paper .

    本文介绍了一种装在S-570扫描电子显微镜中的销-盘式 磨损 试验装置。

  • The wear tests with ring on block wear test machine and corrosion tests were carried out .

    用环块 磨损 试验机进行了 磨损 试验，并进行了腐蚀试验。

  • Wear test and plain strain fracture toughness test have been conducted .

    做了 接触 疲劳试验& 磨损 试验和平面应变断裂韧性试验。

  • The properties of nanocomposite coatings and common coatings have been studied by means of adhesion impulsion and flowing wear test machine which include adhesion impulsion-resistance and abrasion resistance .

    采用了附着力测定仪、冲击试验器、冲蚀 磨损 试验机等手段，对纳米复合涂层、普通涂层的附着力、耐冲击性和抗冲蚀磨损性能进行了研究。

  • A resistance-wear measuring method has been used in wear test .

    磨损 实验中采用电阻磨损测试法。

  • Behavior testing and errors analyzing on an abrasive wear test device ;

    完成了球塞气 举 试验装置的结构和控制系统设计。

  • The measurement of friction force is important in the design of friction and wear test machine .

    摩擦力的测量始终是摩擦 磨损 试验机的重要组成部分之一。

  • The simulation test of heavy rail straightening has been completed on M200 wear test machine .

    在M200 磨损 试验机上对重型钢轨的矫直过程进行了模拟试验。

  • The paper covers introductions of ordinary rubber wear test methods and the standards for selecting test conditions .

    介绍最常用的橡胶 磨耗 试验方法和选择试验条件的标准。

  • Study of surface strengthening technology and wear test of diesel engine cylinder liner

    柴油机气缸套表面强化工艺及 磨损 试验的研究

  • Wear test results show that the SiCp / Al composites have fine wear ability than pure aluminum .

    磨损 试验结果表明，SiCp/Al复合材料较纯铝而言，具有优良的耐磨性能。

  • Wheel wear mechanism and influencing factors were analyzed . The wheel wear law and changes of surface quality were examined based on grinding wheel wear test .

    本文就砂轮磨损机理和影响因素进行了分析，利用砂轮 磨损 试验考察砂轮磨损规律和表面质量的变化。

  • The microstructure and properties of electroless plated Ni-P coating are systemically investigated by employing XRD SEM electrochemical anodic polarization curve measurement and wear test .

    采用XRD与SEM分析技术、电化学阳极极化曲线测试和 摩擦 磨损 试验等，系统地研究了FS-1化学镀Ni-P镀层的结构和性能。

  • The mechanism of friction and wear of different temperature range was discussed by the analysis of the results of Friction and wear test through SEM and EDS. Compared with other high quality products which from domestic and foreign .

    运用SEM和EDS对样品的 磨损表面进行了分析，讨论了不同温度范围内的摩擦 磨损机理，并与国内外优质的摩擦材料进行性能对比。

  • The tribological performances of nano-Cu additive were tested in the condition of different loads by friction wear test machine .

    通过摩擦 磨损 试验机测试纳米铜添加剂在不同载荷下的摩擦学性能。

  • Optimization of Laser Surface Texturing Based on Friction and Wear Test

    基于摩擦 磨损 特性的激光表面造型 试验研究

  • Aerial craft brake movable piece produced with new heat treatment process have basically met the special requirements of wear test .

    运用该工艺生产的航空刹车副动片基本满足了 磨损 试验的特殊要求。

  • Rolling contact fatigue test and wear test are mainly carried out besides the conventional mechanical performance tests for materials above .

    对上述试验材料除进行常规力学性能试验外，主要进行了滚动接触疲劳试验和 磨损 试验。

  • Metallic materials-Wear tests-MM mode wear test

    GB/T12444.1-1990金属磨损试验方法MM型 磨损 试验

  • Standard Test Method for Ranking Resistance of Materials to Sliding Wear in Block-on-Ring Wear Test Using Micro-Tribometer mod .

    标准试验方法排行电阻材料的滑动磨损块上环 磨损 试验用微摩擦国防部。

  • Tribological performances of ZnO nano-particles as lubricating oil additives were studied in friction and wear test machine .

    将制成的ZnO纳米微粒作为润滑油添加剂，在摩擦 磨损 实验机上对其摩擦学特性进行了研究。

  • Natural water was used as lubrication medium the frictional coefficient of water-lubricated integer bearings of different rubber underlayer thickness and hardness was studied by using MPV-20B model friction and wear test machine . The change rule of the frictional coefficient was found and friction mechanism was analyzed .

    以自然水为润滑介质，用MPV-20B型摩擦 磨损 试验机分别研究了不同橡胶层厚度和硬度的水润滑整体式轴承的摩擦因数，得到了它的变化规律并对作用机理进行了分析。

  • The ferrography analysis technology is used to monitor the whole testing process in contact fatigue wear test . The forming mechanism of ball wear particles in contact fatigue wear test is explained in the analysis of monitoring results .

    在接触疲劳 磨损 试验中，应用铁谱分析技术对整个试验过程进行工况监测，通过对监测结果的分析，阐明了接触疲劳磨损试验中球形磨损微粒形成的机理。

  • When the coatings were in lubricated wear test the coefficient of friction rapid reduce to 0.12 .

    陶瓷层涂抹润滑油后，与 钢球对 磨的摩擦系数降低至0.12。

  • The results of wear test hardness and crystallinity measurement show that the filling materials will lower the crystallinity .

    结晶度 测试、 摩擦学性能 测试及硬度 测试结果表明：填充材料不同程度降低了复合材料的结晶度，而结晶度的降低表征了材料 耐磨性能的提高和减摩性能的降低。

  • The wear test was carried on a nozzle which was made from carbides and ceramics on high pressure abrasive water-jet machine .

    本文采用硬质合金和陶瓷材料制成喷嘴，在高压水设备上进行了 磨损 实验研究。

  • The raised material should be smoothed away before the commencement of the wear test .

    在 磨损 试验开始之前应将隆起的材料弄平。

  • A to-and-fro wear test apparatus was devised to investigate the tribological properties of fresh swine thighbones under various lubrication conditions .

    自行设计了一种往复运动的 摩擦 磨损 试验机，在该试验机上对新鲜猪股骨在不同润滑方式下的摩擦学特性进行了研究。

  • The development and test methods are described of the ring-traveller wear test machine .

    本文介绍了钢领钢丝圈 磨损 试验机的研制结果和试验情况。