A new method of fiber / droplet tension test was developed to study the stress transfer behavior of the fiber interface especially fiber coating stress transfer .

其次，发展了纤维／微滴 拉 仲 测试新方法来研究界面上的应力传递行为，特别探讨了纤维涂层对应力传递的影响。

The structure of acidic components and its contribution to emulsification in basic water were investigated by element analysis infrared spectrum interfacial tension test and emulsifying ability test .

通过元素分析、红外光谱、界面 张力和乳化能力 测定考察了超稠油中酸性组分的结构及其在碱水中对乳化的贡献；

In the first part of the experiment students will subject an ordinary steel reinforcing rod to a tension test using a testing machine designed specifically for that purpose .

在第一部分，学生要用为此特制的实验仪器对一根普通预应力钢杆做 拉力 实验。

It is put forward that the analysis method of fracture surface of metallic tension test specimen is available .

提出的金属 拉伸 试样断口分析方法是可行的。

Research on Tension Control System in Fiber Winding and Placement and Design of the Tension Test Platform

纤维铺缠设备中张力控制器及 张力 测试台研究

Finally the new system model is validated by a set of uniaxial tension test data of concrete which had been performed by authors in the laboratory .

最后，通过在实验室完成的一组混凝土单轴 拉伸 试验验证了这个系统模型的合理性。

The relationship between the tensile stress and the tensile strain at the initial of a tension test has been experimentally determined and analyzed .

本文对电流变液的直流 高压 电场作用下，小应变范围内的 拉伸应力应变过程进行了 测试和分析。

The micro-yield strength after different stabilized treatment and dimensional stability in thermal cycling conditions of SiCP / 2024Al composites were measured by tension test and dilatometer .

利用万能 拉伸 试验机和热效应自动分析仪测试了SiCP/2024Al复合材料在不同稳定化工艺处理后的微屈服强度和热循环条件下的尺寸稳定性；

Through the analysis on the axial tension test results of steel fiber reinforced concrete this paper explores steel fiber volume ratio and concrete strength grade upon the axial tension initial cracking strength .

通过对钢纤维混凝土轴 拉 试验结果的分析，研究了钢纤维体积率、混凝土强度等级对钢纤维混凝土轴拉初裂强度的影响。

The free vibration theory of cable is the theory basis of cable tension test and calculation .

索的自由振动理论是索 力 测试和计算的理论基础。

Several commonly used cable tension test methods are summarized . Outline the research state of vibration-based method in cable tension test and then show the existing problems in the flexural rigidity identification of cable . 2 .

主要研究工作包括：1.总结目前工程上常用的几种索 力 测试方法，概述了目前工程应用最为广泛的振动法测索力的研究现状，并指出了识别索的抗弯刚度存在的问题。

In addition uniaxial tension test fails to accurately reflect the complex stress state of tube plastic forming .

单向 拉伸 试验也不能精确反映管材在实际塑性成形中所处的复杂应力状态。

Force and deformation of ring specimen during hoop tension test were analyzed .

通过等宽试样和标距试样 拉伸 实验，对理论分析结果进行了 验证。

If the flexural rigidity of cable can be identified beforehand It will bring a lot of convenience in cable tension test and calculation .

若能事先识别出索的抗弯刚度，将给索 力 测试和计算带来很大的方便。

The process accuracy was validated by the uniaxial tension test .

同时利用 拉伸 试验验证该方法的准确性。

The high temperature plastic deformation of a new-type Al-Cu-Li alloy is studied by high temperature compression test and high temperature tension test on Gleeble 1500 thermal-mechanical simulator and the deformation microstructure of the alloy after high temperature deformation is investigated by SEM and TEM .

采用Gleeble-1500热模拟机高温压缩与高温 拉伸 试验，对一种新型Al-Cu-Li系合金的高温塑性变形进行了研究，并利用扫描电镜和透射电镜对该合金高温变形后的组织进行了观察。

Secondly it is introduced that a new applied standard metal mold tension test specimen is designed .

介绍了一种新的实用标准金属型 抗拉 试样。

The tension test at room temperature is used to study the size effect of thin copper sheet with different crystal size different thickness and different strain rate .

对所制备的薄铜板进行了室温 拉伸 实验，研究薄铜板在不同晶粒大小、不同板厚和不同应变速率下的尺寸效应。

By the triaxial tension test there are three different failure forms of the samples under different consolidation pressure .

三轴 拉伸 试验发现，随着围压σ1的变化，试样有三种不同的破坏形式：纯拉断、先剪切伸长后拉断和纯剪切。

An experimental study is performed on the measuring characteristics of BOTDR for structural health monitoring including dead weight tension test and optical fiber compression-tension test .

应用BOTDR检测技术对用于结构物健康监测的光纤变形检出特性进行了试验研究，包括光纤锥重 拉伸 试验和光纤压缩与拉张试验。

To determine the lift device selection a rotor tension test platform is made .

为确定升力装置的选型，设计了旋翼 拉力 测试平台， 通过多次 试验，得出电机／旋翼的最佳工作区间。

This paper aimed at acquiring the real interlaminar shear strength in tension test .

在 拉伸 负荷方式下，层间剪切强度的 测定 受弯曲力矩的影响。

By comparing with common tension test the amount of test can be lessen largely ;

与常规的 拉伸、压缩 试验相比，可大大地减少试验工作的工作量；

To prove the shock when rolling tension begins to be built a load sensor is located in the midst of work pieces between two stands to do the tension test when the loop has being absorbed .

为证明张力建立初期存在冲击，在两架连轧机轧件中间接入力传感器，进行连轧活套吸收后建立 张力 的 试验。

Methods : Tension test machine and microhardness tester were used .

方法：用 拉力机、显微硬度机 测试。

In this paper the tension test is carried out at various loading rates of 1-500mm / min at a temperature of-110 ℃ for a pressure vessel steel ( 16MnR ) and the mechanical properties at different strain rates are measured .

本文在-110℃和1～500mm／min的加载速率范围内，对一种压力容器钢16MnR进行了不同加载速率下的 拉伸 实验，测量了该钢在不同应变率下的拉伸力学性能。

In this paper the data acquisition and data processing of a microcomputer equipped tension test are presented .

在 拉伸 试验中利用微机进行数据采集和数据处理，从而达到对该 常规 试验 测试现代化的目的。

A New Method for Uniaxial Tension Test of Polyester Cord

一种聚酯帘线单向 拉伸 试验的新方法

Using scaling tension test method simulated the effect of leveling elongations on yield strength ratio of hot dip galvanized dual phase steels .

研究了氮含量对热镀锌双相钢拉伸性能的影响，用定 拉伸 试验方法模拟了平整伸长率对热镀锌双相钢屈强比的影响。