Research on the Parameters of Work Roll Wear Model in Silicon Strip Rolling

硅钢 板轧制中工作辊 磨损模型参数的研究

Non uniform wear of backup rolls in hot strip rolling and its solution measurement

板 带钢热轧支持辊不均匀 磨损及其解决措施

Wear Model for Back-Up Roll on Wide Hot Strip Tandem Mills

宽带钢热 连轧支承辊 磨损模型研究

The wear of the work roll for the hot temper mill are different from that in hot rolling and cold rolling . The wear of the work roll may affect strip profile directly .

热轧带钢平整机工作辊的磨损具有与热轧和冷轧工作辊 磨损不同的特点，而 磨损又直接影响 板形。

Meanwhile the cladding of formation between metal vapor and copper-matrix can reduce contact resistance at the contact zone and the probability of electric arc occurring and thus reduce electrical sliding wear rate of the contact strip .

同时金属蒸气与铜基体形成的合金覆层降低了接触区的接触电阻，减小了电弧产生的几率，从而使得 滑板的载流 磨损率降低。

Influence of work roll 's wear on quality of strip steel and its control

CSP 热 板 带 轧机工作辊 磨损对 带钢质量的影响与控制

Roll wear on finishing train of 2050 CVC Hot Strip Mill

2050CVC热 连轧机精轧机组轧辊 磨损的研究

In order to reduce the wear of the contact line and the contact strip to the least the area of copper alloy contact wire should adopt carbon contact strip .

为了将接触线与 滑板 的 磨耗降到最低，铜合金接触导线区宜采用碳滑板。

Study and Realize Roll-Type & Wear Degree Detection System of Plate Strip Rolling

板 带钢轧辊辊型及其 磨损检测系统的研究与实现

Friction and Wear Behavior of Copper-Impregnated Metalized Carbon Strip Sliding against Stainless Steel with Electrical Current under Elastic Condition

弹性条件下浸金属碳 /不锈钢载流摩擦 磨损性能

The effect of the backup roll contour and the roll thermal wear on the load distribution between rolls and the exit strip crown was studied .

研究了支撑辊辊型曲线及轧辊热 磨损对辊间压力分布和 带钢出口凸度的影响。

Using metallographic method the wear of the coupling copper slide block of hot strip mill qualitatively studied .

采用金相分析方法，对 热轧机万向接轴内铜滑块的 磨损现象进行了定量分析。

The wear mechanism of work rolls in finishing trains of hot strip mills is analysed .

分析了 热轧精轧机组工作辊的 磨损机理；

The results showed that the electrical sliding wear rate of the resin-calcination type contact strip increases with the increase of current density and the sliding velocity .

研究表明，树脂焙烧型 滑板的载流 磨损率随载流密度和滑行速度的增加而增大。

Based on the structure and property of resin-type function composite well controlled and relatively simplicity in manufacture the preparation process and wear behavior and anti-wear mechanism of the resin-type contact strip materials were investigated in this paper .

本文基于树脂型功能材料的结构和性能具有良好可控性及其成型工艺相对简单等特点，开展了对树脂型 滑板材料的制备、 磨损性能及抗磨机理研究。

Effects of Arc Discharge on Friction and Wear Properties of Metal-impregnated Carbon Strip Sliding against Cu Trolley under Electric Current

电弧能量对浸金属碳 滑板材料载流摩擦 磨损性能的影响

In the presence of electric current the wear volume of pure carbon strip decreases with the increasing of normal force and increases with the increasing of electric current intensity .

加载电流时，纯碳 滑板 的 磨损量随法向压力的增大而减小，随试验电流的增大而增大。

Wear and wear mechanisms of aluminum strip in cold rolling

铝板冷轧磨损及 磨损机制

The results showed that current is the most important factor which affects the wear rate of the resin hot-pressing type contact strip and the wear rate increases with the increase of current density .

研究表明，电流是影响树脂热压型 滑板 磨损率的最主要因素，其磨损率随载流密度的增加而增大。

Microstructure and Wear Resistance of Steel / Al-Pb Alloy Composite Strip Made By Spray Forming

喷射成形钢/AlPb轴瓦合金复合 板材的组织及 耐磨性

In order to resolve the problems that contact strip is difficult to coordinate the coupling system of pantograph / catenary due to material defect to avoid high abrasion with current and to reduce the wear rate of contact strip .

为了克服现有滑板因自身材质的缺陷难以协调弓网耦合系统载流磨损过大等问题，进一步降低 滑板的载流 磨损率。

Study on roll wear on hot strip rolling mill

热带钢轧机轧辊 磨损研究

The theory of computation of roll wear of hot strip finishing mill

热带 钢 连 轧机精轧轧辊 磨损计算理论

But the peak of contact pressure between rolls forms when the intermediate roll shifts which leads local wear of rolls and quality defects of strip .

但由于中间辊轴向窜动后，在工作辊与中间辊、中间辊与支撑辊间形成接触压力峰值，导致轧辊局部 磨损及 带材 表面质量问题。

Microstructure and wear resistance of spray formed steel / Al-Pb composite strip after spray forming rolling and annealing were studied .

对喷射成形制备的钢/AlPb合金复合 板材的微观组织，轧制和退火处理后的组织及 耐磨性进行了研究。

Lubrication rolling can evidently decrease rolling force and resource wastage and greatly reduce roller wear and improve strip surface quality and effectively increase the productivity which makes thick strip rolling be possible .

使用热轧润滑轧制技术能显著降低轧制力，降低能耗，减少轧辊 磨损，改善 带钢表面质量，有效提高生产率，使轧制薄规格带钢成为可能。

Due to its good mechanical properties and wear resistance rubber rollers are commonly used in strip production process .

橡胶胶辊由于其良好的机械性能及 耐磨性，常用于 带钢涂镀工艺中。

Preparation and Investigation of Wear Behavior and Anti-wear Mechanism of Resin-type Pantograph Contact Strip Materials

树脂型受电弓 滑板材料的制备与 磨损特性及抗磨机理研究