According to the actual application of operating experiment in the thrust bearing test board the designed oil film thickness VXI measuring system shows better performance .

通过应用于 推力 轴承试验台的实测中，该油膜厚度VXI检测系统显示了良好的性能。

Influence analysis of pad geometrical parameters on thrust bearing 's lubrication performance

推力瓦块几何参数对 推力 轴承润滑性能的影响分析

Model Experiment of Gas Permeability Distribution Rule around Dense Boreholes Investigation of Pressure Distribution of Partial Porous Aerostatic Thrust Bearing

密集钻孔周围透气性分布规律的模型实验局部多孔质气体静压 止 推 轴承压力分布的研究

Example of fault diagnosis on main thrust bearing based on vibration and lube analysis

基于振动和润滑油分析的主 推力 轴承故障诊断实例

Production and application of thrust bearing and guide bearing made of filled PTFE in submarine motor pump are introduced .

介绍了潜水泵 中止 推 轴承与导向轴承用填充聚四氟乙烯材料进行的生产和应用。

Measurement and Research on Water Film Thickness of Thrust Bearing for Canned Motor

屏蔽电动机 推力 轴承水膜厚度测试研究

Residual oil can be drained via valve at the rear of gear reducer and oil drain valve in thrust bearing oil sump .

残油的排放可由减速机尾部的阀门和 推力 轴承油池的放油阀门来进行。

It is made suggestions for the criterion of hardness and precision of the thrust bearing runner .

对 镜 板的硬度和精度的限值提出了建议。

Development of New Sintering Turbocharger Thrust Bearing

新型涡轮增压器烧结 止 推 轴承材料的研制

Actual deviation of height of the spherical plain thrust bearing .

推力关节 轴承实际高度偏差。

This paper presents a method for analyzing deformation of thrust bearing with Teflon layer for hydrogenerators and designing surface shape .

本文介绍了水轮发电机弹性金属塑料瓦 推力 轴承的变形分析和瓦面形状的设计方法。

Static Characteristic Analysis of Aerodynamic Gas Thrust Bearing Based on Finite Difference Method

基于有限差分法的动压气体 止 推 轴承静态特性分析

Analysis of Deformation of Double-disk Supported Thrust Bearing for Hydrogenerators

水轮发电机双托盘支撑 推力 轴承变形分析

Design of A Device for Testing the Static Characteristics of Aerostatic Thrust Bearing

空气静压 止 推 轴承静态性能测试装置设计

With the increasing of the rotational speed the water film pressure and the load capacity of the elastic-metal-plastic thrust bearing were reduced by50 % .

随转速的增大，界面滑移现象对水膜压力和 轴承 承载能力的削减程度明显增大，水膜压力和 轴承承载能力将降低50%左右。

Performance analysis and design improvement of thrust bearing bush in a large vertical pump unit

大型立式水泵机组 推力 瓦性能分析及改进设计

A core regulating pad ring is padded on the lower ring of the thrust bearing which can make the hook swing in any directions corresponding to the connecting cylinder .

在 推力 轴承下圈垫上调心垫圈，可使吊钩相对连接筒在任意方向上摆动。

A permanent magnet thrust bearing was employed to stabilize the rotor in axial direction .

应用高磁场稀土钕铁硼永磁铁 推力 轴承，实现转子的轴向稳定。

A Study on Characteristics of Air Static Pressure Thrust Bearing with Variable-Section Pressure Equalizing Groove

具有可变均压槽的气体静压 推力 轴承性能研究多孔质气体润滑 轴承设计理论与实验方法

Thermal Transient Behavior of Thrust Bearing under Step Applied Load

阶跃载荷扰动条件下 推力 轴承热瞬态过程研究

Assembly die design of protecting cover of full-ball flat bottom thrust bearing

满球平底 推力 轴承防护罩装配模具设计

Heavy-duty thrust bearing ; locked to prevent axial movement .

坚固耐用的 止 推 轴承；锁定后有利于阻止轴向运动。

Based on the wear law and reliability theory of the thrust bearing the mathematical model of reliability life calculation on the wear of the thrust bearing is derived .

根据 推力 轴承磨损规律和可靠性理论，导出了 推力 轴承磨损的可靠寿命计算的数学模型。

Numerical Analysis of Lubricating Characteristic of Large Size Sector Hydrostatic Thrust Bearing

大尺寸扇形静压 推力 轴承润滑性能的数值分析

Study on the Precision Forming of HAI 60-1-1 Aluminum Brass Thrust Bearing Blocks

HAI60-1-1铝黄铜 止推 轴承座精密成形研究

This paper studies the influence of pad angle pad face shape and support forms on thrust bearing 's performance by CFD and analyses the influence by traditionary engineering method .

本文通过对影响 推力 轴承工作性能的 推力瓦块的瓦张角、瓦面形面以及支撑形式等主要参数进行分析和研究，对指导 推力 轴承的设计具有重要的工程意义。

Since the gear reducer is working with load attention shall be paid to the temperature increase of axial cone bearing and sliding thrust bearing oil sump .

因为减速机此时已经是带负荷运转，所以应特别注意输入轴锥轴承的温升和滑动 推力 轴承油池的温升有无异常现象等。

With an additional axial thrust bearing both the thrust and radial bearings are preloaded individually .

由于增加了一套轴向 止 推 轴承，所有的推力和向心轴承均被分别预加载。

Reasons and Solutions About Folding Defect in Extrusion Forming of Thrust Bearing

止 推 轴承 座挤压成形过程中产生折叠缺陷的原因及解决方案

Thrust disc is made of steel and thrust bearing bushing surface is made of plastic bushing .

推力盘为钢制材料制成， 推力 轴承瓦面为塑料瓦材料制成。