Stress Analysis and Experiment on the Spiral Wound Gasket
缠绕式 垫片的应力分析和试验
Structural design of a new shape spiral wound gasket
新型 缠绕 垫片的结构设计
Study on Mechanical Properties of Flexible Graphite Wound Gasket
柔性石墨 缠绕 垫片机械性能 试验研究
Compression Performance Analysis of Shaped-Metal Strip of Spiral Wound Gasket
缠绕 垫片成型钢带压缩性能分析
Class 300-600 : Fully-encased spiral wound graphite-filled stainless steel gasket .
600磅级:全封闭螺旋 缠绕石墨填充不锈钢 密封 垫。
The structure of wound gasket was designed by adjusting thickness of flexible graphite gasket band to change winding density . The paper studied mechanical properties of wound gasket with different structures at room temperature .
通过调整柔性石墨填料带厚度改变缠绕密度的方法设计了 缠绕 式 垫片的结构,对不同结构的缠绕式垫片进行了常温机械性能的试验研究。
Meanwhile the performance of graphite spiral wound gasket under different technique parameters was analysed .
同时对不同工艺参数下的石墨 缠绕 垫片性能进行分析。
Analysis of Flange Installation Requirements for Spiral - wound Gasket
缠绕式 垫片法兰接头装配要求的剖析
Structural Design and Strength Calculation for a New Type of the Earring-type 's Spiral Wound Gasket
新型耳环式 缠绕 垫片的结构设计与强度计算
Recovery performance of W-shape matallic flexible graphite spiral wound gasket exceeds over ten percentage on nation standard and reaches international advanced level .
W形金属柔性石墨 缠绕 垫片的回弹性高出国标十几个百分点,达到了国际先进水平。
The compressive-resilient performance the creep performance and the leakage behavior of three types of gaskets namely flexible graphite gasket with tanged metal sheet spiral wound gasket filled with flexible graphite and metallic enveloped gasket were investigated .
试验研究了柔性石墨填充 缠绕 式 垫片、金属冲齿板柔性石墨复合垫片和金属包覆垫片的压缩回弹性能、蠕变性能和基本密封性能;
Characteristic Study of Stress Relaxation on V-type Metallic Spiral Wound Gasket
V型金属 缠绕 垫片应力松弛特性 试验研究
Valves in these classes are also available with spiral wound gasket bonnet joints when specified .
如果用户要求,对于这些压力等级的阀门,我们也可以提供螺旋 盘绕 垫圈阀盖连接。
Studies of Structure and Technology Parameters of Graphite Spiral Wound Gasket
石墨 缠绕 垫片的结构与工艺参数的研究
An Analysis and Experiment Investigation on Pre-Stress of Spiral Wound Gasket
金属 缠绕 式 垫片的预紧应力分析及试验研究
Development of high temperature high pressure W type spiral wound gasket
高温高压W型 缠绕 垫片的研制
The Domestic Development of Spiral Wound Gasket Applied on Import Screw Locking Heat Exchanger
引进螺纹锁紧环换热器 缠绕 垫的国产化研制
The sealing design criteria to measure the factors of spiral wound gasket were adopted based on this bolt loads of flange can be determined by using the new PVRC method .
采用密封设计准则,通过试验确定了金属 缠绕 式 垫片 的 垫片系数,在此基础上,按照PVRC新方法对法兰螺栓载荷进行了计算。
The V-type steel belt of metallic spiral wound gasket is theoretically analyzed . The gaskets are verified through reasonable structure design and performance test .
对金属 缠绕 垫片的V形钢带进行理论分析,通过合理的结构设计、性能实验加以验证。
美[wund ˈɡæskɪt]英[wu:nd ˈɡæskit]
缠绕垫