test specimen

试件试样,试棒,试块

  • The titration of water is usually carried out with the use of anhydrous methanol as the solvent for the test specimen ;

    水分的滴定通常是用无水甲醇作 物质的溶剂来完成的。

  • A corresponding analytical system named TDGS was proved to be quite effective in simulating a prototype test specimen .

    相关的 TDGS分析系统针对原型 试验取得了较好的模拟效果。

  • The spectral reflectance of each test specimen is measured in situ before and after exposures .

    在辐照前后对每一个 试样的光谱反射系数进行了原位测量。

  • The tensile test indicated that the laser cutting test specimen does not have the obvious necking in the stretch process and it breaks immediately after necking .

    拉伸试验表明激光切割 试样拉伸过程中没有明显颈缩,在出现颈缩后马上断裂。

  • The test specimen may be titrated with the Reagent directly or the analysis may be carried out by a residual titration procedure .

    样品可能会被卡尔试剂直接滴定,或者采用回滴定法完成分析。

  • In the first place it is pointed out defects of national standard metal molding tension test specimen for casting aluminum alloy in this paper .

    指出了铸造铝合金国家标准金属型抗拉 试样在实际生产过程中存在的问题。

  • In the second part a test program to help improve modeling of SCBF systems is described including the design of a nearly full-size two-story SCBF test specimen .

    在文章的第二部分描述了一个帮助轴心抗拉构件改进建模的实验程序。这部分包括一个接近实际大小的两层轴心抗拉构件的 实验 范例

  • The experimental result indicated that : In stretch process in identical test specimen the strain value on metal substrate and contact surface are same the mark is opposite .

    实验结果表明:在拉伸过程中,同一 试样中金属基体上和界面上的应变数值相同,符号相反。

  • There are also separate pieces of mechanical load and simple water pressure test specimen as a contrast .

    此外还有单独机械荷载 件和单纯水压力 作为对比

  • And there is a relation between relative deformation of test specimen and its confinement .

    的相对变形量与其约束状况有一定的关系,不对称约束可能会使 低温下的相对变形量增大。

  • Secondly it is introduced that a new applied standard metal mold tension test specimen is designed .

    介绍了一种新的实用标准金属型抗拉 试样

  • It is put forward that the analysis method of fracture surface of metallic tension test specimen is available .

    提出的金属拉伸 试样断口分析方法是可行的。

  • The ultrasonic echo signal processing method which based on the pulse of the reflection for echo signal processing is studied which can analyze the defects of echo signal characteristics their impact on the test specimen by the internal structure of the change .

    本文采用基于脉冲反射法的超声回波信号处理方法对回波信号进行处理,使用该方法能够分析出缺陷对回波信号超声特性的影响及其被 测试 内部结构的变化情况。

  • By use of the method of welding thermal simulation the morphology in HAZ was simulated and the post-weld heat treatment under different tempering parameter to the test specimen was carried out .

    采用焊接热模拟的方法,模拟HAZ粗晶区组织,并在不同回火参数下对 试样进行焊后热处理。

  • As an application example the model of water-resisting cover of deep sea missile launcher system was designed and its test specimen was prepared .

    作为应用实例,文中设计并制备了深海导弹潜射系统隔水罩的模型 ,并对 进行了 性能 模拟 试验

  • The sample stove can offer the experimental environment for test specimen control the experimental procedure through the control device and receive experimental data and result through the sensing device .

    样品炉为 试验 样品提供试验环境,通过控制装置控制试验流程,通过传感装置得到试验数据和结果。

  • Some factors of influencing representativity of concrete test specimen are discussed and the improving measures are presented in this paper .

    分析了影响砼 强度代表性的几种原因并提出改进措施。

  • Place test specimen on the base surface .

    放在试验基面上。

  • These findings will helpful to standardize the test specimen .

    以上发现有助于 的标准化 设计

  • The result shows that the physical property of test specimen without the case is more similar to that of the generally artificial stone if the proportion of coarse water quenched slag is high .

    研究结果显示,粗水淬熔岩比例较多时所制成无胶壳 之物理性质较接近一般人造石之物理性质;

  • In the Desiccant Method the test specimen is sealed to the open mouth of a test dish containing a desiccant and the assembly placed in a controlled atmosphere .

    在增重法中, 试样被密封在装有干燥剂的透湿杯杯口处,然后将整套透湿杯组件放在控制环境中。

  • Rigless sand control It is necessary coal dust to inspect and evaluate comprehensively all physical-chemical properties of the coal dust as well as to determine its anti-metal penetration ability by pouring a test specimen .

    不用修井机的防砂作业选择煤粉应通过全面的检测和评价各项理化指标,并通过 浇注 试验以确定其防粘砂能力。

  • The fatigue test indicated that the safety life of the laser cutting test specimen is as 8.76 % of the machine-finishing test specimen . Finally the influence of the laser incident angle on cutting quality was studied .

    疲劳试验表明激光切割 试样的安全寿命是机械加工试样的8.76%。最后,研究了激光入射角对切割质量的影响。

  • Adhesives T peel strength test method for a flexible-to-flexible test specimen assembly

    GB/t2791-1995胶粘剂t剥离强度试验方法挠性材料对挠性材料

  • According to the processing performance titanium alloy materials using a CNC machining center processing the tensile test specimen .

    根据钛合金材料的加工工艺性能,采用数控加工中心加工出拉伸 实验所用

  • Based on the finite element analysis we carry out numerical simulation on explaining the differences of compressive strength test values and the failure modes of numerical simulation are basically the same as the test specimen failure modes .

    运用数值模拟有限元分析解释了试验中抗压强度数值的不同,并且数值模拟出来的 破坏形式与试验破坏形式基本一致。

  • In this test quasi-static load is applied to the test specimen for validating the strength of the test specimen and the adequacy of design .

    正弦-脉冲试验是将准静态载荷施加到 上,来验证试件的强度和飞行设计的合理性。