Elastic-Plastic Finite Element Analysis for Unequal-Diameter Tee Joint with Axial Through-wall Cracks at the Shoulder

焊制异径 三 通肩部轴向穿透裂纹弹塑性有限元分析

Describes a J shaped stack developed to meet the requirement of smoke emission standard of oil fired boilers which consists of a slope tee a straight pipe an expansion joint an explosion flap a rain drain pipe and a down pipe .

为满足燃油锅炉的烟气排放要求，设计了J型烟囱，它由斜 三 通、直管、膨胀 节、防爆门、雨漏、落水管等组成；

Analysis on Upward Warping of the Horizontal Ram in Multi-ram Forging Process of High-pressure Tee Joint

高压 三 通多向模锻水平冲头翘曲成因分析

The obtained conclusion provided theoretical basis for further improvement in the design of tee joint .

所得结论为进一步改进 三 通设计提供了理论依据。

The tee joint entity model has been chosen by the study of the influence of diameter of the branch pipe and the length dimension of the run pipe and branch pipe .

研究了不同支管管径、不同管长尺寸的影响，选择了 三 通实体模型；

A new type tee joint reversed valve which was used in negative pressure bag filter with opposite blow is reported .

本文介绍负压反吹风布袋除尘器中一种新型的 三 通换向阀。

Stress Determination of Welded Equi-Diameter Tee Joint

焊接等径 三 通的应力测定

This paper introduced the method and result of conducting a finite element analysis on the cold forged reinforced thick wall tee joint .

本文介绍了对冷锻厚壁加强 三 通进行有限元分析的方法和结果。

The finite element analysis of cold forged reinforced thick wall tee joint

冷锻厚壁加强 三 通有限元分析

The UHMWPE tee joint was made by a kind of specific designed equipment in which the branch pipe and main pipe cut from UHMWPE pipe were welt into integer .

以UHMWPE管材为原料，在特殊设计的设备上，将支管和直管沿交 接线熔接在一起，可制得各种规格的UHMWPE 三 通。

Failure analysis and resolvent on the tee joint of piping system for water distribution

泄 放水系统管路 三 通失效原因分析及对策

This paper introduces a method of positioning of the commonly used tee joint point in pipeline detecting projects .

本文介绍了管线探测工程中常见的 三 通点的一种定位方法。

Positioning method of the tee joint point of underground pipelines

地下管线 三 通点的定位方法

Formation Process of Tee Joint in Automotive Air - conditioner

汽车空调管中 三 通 接头的成形工艺

The method which used to build the unequal-diameter tee joint with axial through-wall crack has been established .

确定了肩部含轴向穿透裂纹 焊制异径 三 通有限元模型的建立方法。

Research on and application of tee joint reverse valve for negative bag filter with opposite blow

负压反吹布袋除尘器 三 通换向阀的研究与应用

Numerical simulation and experimental study on the drawing forming of branch pipe of tee joint

大 口径 三 通 支管拉拔成形数值模拟与试验研究 粘结 型 锚杆拉拔 承载 力的试验与理论分析

The Research on the Cracking of Tee Joint Welding of Main Steam Pipe

主汽管 三 通 焊缝开裂泄漏原因分析研究

Numerical control flame cutting for the groove of tee weld joint

焊接 三 通 相 贯 接头坡口面的数控切割

Pipe series : Elbow tee cross movable joint Bu core reducer pipe cap choke plug inside the wire outside the wire turned-over edge increaser etc.

管件类：弯头、 三 通、 四通、活 接头、卜芯、大小头、管帽、堵头、内丝、外丝、翻边、异径管。